Atas Granutile Panel Manual do Utilizador descarregar pdf

Installation Guide

Review and understand complete

guide before beginning installation.

This guide has been prepared as

suggested details to particular design

conditions. Each condition has certain

limitations to performance, aethetics or economics.

Professionals qualified to assess this information for a

specific project, should determine that the selection and

installation are made to their requirements. ATAS cannot

assume any responsibility for the actual selection and/or

installation of materials. The panels, flashings and trim

shown in this guide, illustrated over solid and plumb sub-

strate, assume that the structure has been designed and

prepared in accordance with local building codes.

Granutile is installed horizontally, from the ridge down. The

panels can be installed over open framing, solid underlay-

ment or over low profile roofing material. When installing

over open framing a vapor barrier is required beneath the

panel. It is recommended to use ATA Guard over a solid sub-

strate or old roofing material. In addition install waterproofing

membrane at all eaves, valleys, hip and ridges. 2” x 2” wood

battens are used to provide a fastening point for the panels.

Space battens as shown below.

Upper panel row overlaps lower row.

The panel should be fastened with

SWR9XX into the wood batten.

Panel sides should overlap as shown.

Panel overlaps

45 3/4”

15 1/2”

1”

Panel size - 15 1/2” nom. x 45 3/4” nom.

with a 1” deep nom. front face

Panel coverage - 14 1/2” nom. x 43 3/4” nom.

Place ATA Guard on the roof overlapping

the bottom row at the eave. Depending on

location, codes, etc. water / ice proofing

membrane may be required at the eaves and

valleys, hips and gables. It is recommended

to leave 1” space between lengths of wood

battens and stagger the spaces up the roof.

The first row of battens should be installed at

the eave.

The second row of battens should be at 14 1/4”

measured from front of first row. The sunse-

quent rows of battens should be 14 1/2” apart.

The top batten is installed at the ridge. The top

panel is measured to size and bent up. This is

done prior to cutting to length to minimize panel

distortion. Then the panel is cut 1” above the

bend to form a water barrier and fastened to

the wood batten. The second row is slipped

behind the front face of the top row and fas-

tened through both panels into the batten.

Lay-out of

Horizontal Furring

Components

14 1/4”

14 1/2”

14 1/2” spacing

up the roof

required

Wood Batten

cant strip

1 2 3 4

Resumo do Conteúdo

Página 1 - Installation Guide

Installation GuideReview and understand completeguide before beginning installation.This guide has been prepared as suggested details to particular de

Página 2 - Valley Detail

Eave DetailGable DetailValley Detail1. Install Cant Strip as shown behind the first 2” x 2”batten.2. Apply ATA-Shield** along eave and up the roof to

Página 3 - Headwall Detail

Hip & Ridge DetailHeadwall DetailAT THE RIDGE1. After installing all the wood battens up theroof, measure the distance between the lasttwo rows.

Página 4 - Sidewall Detail

Pipe DetailStep 1Cut on the proper pipediameter marked on the flashing. Step 2Position over pipe and slidedown the pipe.Step 3Apply polyurethane seala

Comentários a estes Manuais

Sem comentários

Atas Granutile Panel Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para a casa Atas Granutile Panel. ATAS Granutile Panel User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Para a casa Atas Granutile Panel